Popular Design for Bronze Foundry - Aluminium Casting Product by Sand Casting – RMC Foundry Detail:
China custom aluminium alloy castings by sand casting and shell mold casting processes.
The term Green Sand denotes the presence of moisture in molding sand and indicates that the mold is not baked or dried. Raw sand is mined and then processed to give it a consistent distribution of grain sizing. When processed for molding, organic clays are added to bond the grains together.
A coal dust (known as Sea Coal) is added to control casting quality during expansion of the sand when hot metals are poured into the molds. Other additives, such as pitch, cellulose and silica flour, are also used. The additive used depends on the metal cast. The sand is blended in a mullor or mixer, where the water and the additives are blended with the sand.
The sand is then ready to be used to make a mold. There are several methods of molding but all methods squeeze or compact the sand against a pattern to make an impression of the part to be cast. The patterns are separated from the mold halves or mold cake and the mold is then closed creating a part cavity. Types of molding range from automatic high-pressure high-speed molding, automatic match plate molding, automatic tight flask molding (used for large molds) and jolt squeeze molding. Large molds are also made on the floor and rammed up by hand. Today, molding is primarily done automatically and the molds are placed on mold handling equipment to be poured, to allow the castings to solidify and to cool. Mold handling equipment configurations include indexing lines, looping lines and mold car lines. Pouring of the metal can be accomplished automatically with a pouring furnace or transported to the molds in ladles. Ladle capacities can range in size from 100 pounds up to several tons.
After the metal in the mold has solidified and cooled, the mold is dumped onto a shakeout that separates the castings from the sand. The shakeout process can be performed with a wide variety of equipment. The casting is then desprued (separated from the runner system). The runner system is used to get metal into the casting cavity. The runner system is sent back to the melt department for reuse and the castings are sent to the finishing process. The sand is reused after it is screened and cooled. New sand is also added based upon a ratio of the amount of metal poured into a given quantity of sand.
Casting finishing normally starts with shot blasting to remove sand that is stuck to the casting. The finishing area can be highly automated, using robots and Vision systems, or it can be a simple manually operated hand system. Normal types of finishing work include wheel grinding, belt grinding, trim press cutting, saw cutting, air arch cutting and hand grinding. Method used depends on the metal cast and the size of the casting.
Aluminium and its alloys could be cast and poured by high pressure die casting, low pressure die casting, gravity casting, sand casting, investment casting and lost foam casting. Usually, the aluminum alloy castings have less weight but complex structural and better surface.
What Aluminium Alloy We Cast by Sand Casting Process:
• Cast Aluminium Alloy by China Standard: ZL101, ZL102, ZL104
• Cast Aluminium Alloy by USA Stardard: ASTM A356, ASTM A413, ASTM A360
• Cast Aluminium Alloy by other Starndards: AC3A, AC4A, AC4C, G-AlSi7Mg, G-Al12
Unified | Aluminium association | Hardness BHN | Ultimate tensile strength, MPa | Yield Strength, MPa | Modulus of elasticity, GPa | Fatigue Strength, MPa |
A03550 | AA355.0 | 75-105 | 255 | 185 | 70.3 | 69.0 |
A03600 | AA360.0 | 75.0 | 300 | 170 | 71.0 | 138.0 |
A03800 | AA380.0 | 80.0 | 317 | 159 | 71.0 | 138.0 |
A03830 | AA383.0 | 75.0 | 310 | 152 | / | 145.0 |
A03840 | AA384.0 | 85.0 | 331 | 165 | / | 140.0 |
A03900 | AA390.0 | 120.0 | 280 | 240 | 81.2 | 140.0 |
A04130 | AA413.0 | 80.0 | 296 | 145 | 71.0 | 130.0 |
A04430 | AA443.0 | 30-60 | 145 | 48.3 | 71.0 | / |
A05180 | AA518.0 | 80.0 | 310 | 193 | 69.0 | 160.0 |
Aluminum Alloy Castings Characteristics:
• The casting performance is similar to that of steel castings, but the relative mechanical properties decrease more significantly as the wall thickness increases
• The wall thickness of castings should not be too large, and other structural features are similar to those of steel castings
• Light weight but complex structural
• The casting costs per kg of aluminium castings are higher than that of iron and steel castings.
• If produced by die casting process, the mold and pattern cost would be much higher than other casting processes. Therefore, die casting aluminium castings would be more suitable for castings of large demanding quantity.
Typical Chemical Composition of Investment Casting Aluminium Alloy by North American Specifications | ||||||||||||||
Alloy Grade | Specification | Al | Cu | Si | Zn | Mg | Cr | Fe | Mn | Ti | Ag | Be | Ni | P |
A356-T6 | AMS 4218 | Bal | 0.20 | 6. 5 – 7. 5 | 0.10 | 0.25-0.45 | - | 0.20 | 0.10 | 0.20 | - | – | - | - |
A 357 | AMS 4219 | Bal | 0.20 | 6. 5 – 7. 5 | 0.10 | 0.40-.70 | - | 0.20 | 0.10 | 0.04-0.20 | - | 0.04-0.07 | - | - |
F 357 | AMS 4289 | Bal | 0.20 | 6.5-7.5 | 0.10 | 0.40-.70 | - | 0.10 | 0.10 | 0.04-0.20 | - | 0.002 | - | - |
E 357 | AMS 4288 | Bal | - | 6.5-7.5 | 0.10 | 0.55-0.60 | - | 0.10 | 0.10 | 0.10-0.20 | - | 0.002 | - | - |
A201 | AMS 4229 | Bal | 4.0-5.0 | 0.05 | - | 0.15-0.35 | - | 0.10 | 0.20-0.34 | 0.15-0.35 | 0.40-1.0 | - | - | - |
C355 | AMS 4215 | Bal | 1.0-1.5 | 4.5-5.5 | 0.10 | 0.40-0.60 | - | 0.20 | 0.10max | 0.20 | - | - | - | - |
A206 | AMS 4235 | Bal | 4.2-5.0 | .05max | 0.05max | 0.20-0.35 | - | 0.10ma | 0.20-0.50 | 0.15-0.30 | - | - | 0.5max | - |
B206 | Bal | 4.2-5.0 | .05max | 0.05max | 0.15-0.35 | - | 0.10max | 0.20-0.50 | 0 1 0 | - | - | 0.5max | - |
China Sand Casting Foundry
Product detail pictures:
Related Product Guide:
We constantly function like a tangible group to ensure that we can give you the very best high-quality and also the very best cost for Popular Design for Bronze Foundry - Aluminium Casting Product by Sand Casting – RMC Foundry, The product will supply to all over the world, such as: America , Ethiopia , Borussia Dortmund , We follow up the career and aspiration of our elder generation, and we're eager to open up a new prospect in this field, We insist on "Integrity, Profession, Win-win Cooperation", because we have now a strong backup, that are excellent partners with advanced manufacturing lines, abundant technical strength, standard inspection system and good production capacity.
By Evelyn from Danish - 2018.07.26 16:51
Reasonable price, good attitude of consultation, finally we achieve a win-win situation,a happy cooperation!
By Linda from Albania - 2018.06.30 17:29